Máy hiện sóng tương tự Pintek PS-251 (25MHz With Component Test, 2 channel)

Hãng sản xuất : Pintek - Taiwan
Xuất xứ : Taiwan

25MHz, ALT Trigger.
1mV sensitivity.
10ns Resolution.
Component test, Beam-finder
Illuminate, Hold-off, X-Y 

Type: Rectangular with integral grateful. 
Display Area: 8 x 10 div (1 div= 1 cm) 
Accelerating Voltage: 2.1 kV. 
Phosphor: P31 
Vertical amplifiers (CH 1 and CH 2) 
Sensitivity: 5 mV/div to 5V/div (X1 mode). 
                      1 mV/div to 1V/div (X5 mode). 
                      1-2-5 sequence, 10 step attenuator. 
                      Vernier control provides full adjustable 
                       attenuation between steps. 
Accuracy: ±3% (X1 mode). ±5% (X5 mode). 
Input Resistance: 1 M±2% 
Input Capacitance: 25 pF//10pF. 
Frequency Response: 5 mV to 5 V/div (CAL): DC 
                                         to 25 MHz (-3 dB) 1 mV/div 
                                         (CAL): DC to 10 MHz (-3 dB) 
Rise Time: Approximately 14.0ns. 
Operating Modes: CH1 : CH 1, single trace. CH2 : CH 2, 
                                  single trace. ALT : dual trace, alternating. 
                                  CHOP : dual trace, chopped. ADD :
                                  algebraic sum of CH 1 + CH 2 
Polarity Reversal (Invert): CH 2 only. 
Maximum Input Voltage: 400 V dv + ac peak 
Maximum Undistorted Amplitude: DC-to-25 MHz : 4 divisions. 
                                                                DC-to-15 MHz : 8 divisions. 
HORIZONTAL AMPLIFIER (Input through channel 1 input) 
X-Y mode : switch selectable using X-Y switch. 
                      CH 1 : X axis CH 2 : Y axis 
Sensitivity: 1mv/div to 5v/div 
Accuracy: Y-Axis : ±3% ±X-Axis : ±6% 
Input Impedance: 1M//25PF 
Frequency Response: DC to 1 MHz typical (-3 dB) 
X-Y Phase Difference: Approximately 3o at 50 kHz. 
Maximum input Voltage: 400Vdc+ac peak 
SWEEP SYSTEM 
Sweep Speed: 0.1 μs/div to 2 s/div in 1-2-5 sequence, 
                          23 steps. Vernier control provides fully 
                          adjustable sweep time between steps. 
Accuracy : ±3% 
Sweep Magnification:10X, ±6% (0.1 μs and 0.2 μs ranges 
                                         uncaliubrated when X10 is engaged). 
Holdoff: Continuously adjustable from NORM to 5 times normal. 
TRIGGERING 
Trigger Source: CH 1, CH 2, ALT, EXT, LINE. 
Maximum External Trigger Voltage: 300V dc + ac peak. 
Trigger Coupling: AC: 30 Hz to 30 MHz TV - H : Used for 
                                   triggering from horizontal sync pulses. 
                                   TV - V: Used for triggering from vertical sync pulses. 
Trigger Sensitivity: Internal : 0.5 division (1 division with TV 
                                     Coupling) External : 500 mV 
OTHER SPECIFICATIONS 
COMPONENT TEST: 
Test Voltage: Max. 6 Vrms (open circuit). 
Test Current: Max. 11 mA(shorted). 
Test Frequency: Line Frequency 
Components : Capacitor, Inductor, Diode, Transistor, Zener etc. 
BEAM FINDER: Trace can be return to CRT center area when 
                               press beam finder button. 
GRATICULE ILLUMINATION: Adjustable 
Calibration Voltage: 1 kHz (nominal) Positive 
                                      Square Wave, 2.0 V p-p (±3%) 
Trace Rotation: Electrical, front panel adjustable. 
Power Requirements: 115/230 VAC ±10%, 50/60Hz 
Dimensions: 324 x 132 x 398 mm (12.8 x 5.2 x 15.6"). 
Weight: Approximately 7.6kg (16.75bs).